GREENHOUSE PLANNING / GROWING

How much airflow does a greenhouse need?

Calculate exchange time from installed exhaust flow, then coordinate the American Roots crop zone, wet wall and SwarmDep operating mode.

Calculate the air volume you are serving

Nominal exchange time in minutes equals enclosed volume in cubic feet divided by delivered exhaust airflow in CFM. This calculation helps compare greenhouse sizes and operating modes. Real air mixes as it travels, so one calculated exchange does not mean every pocket of air has been replaced.

American Roots' geometry model distinguishes the whole greenhouse from the crop compartment beneath closed SwarmDep curtains. Use the relevant volume when discussing the equipment for your chosen length.

EXAMPLE AIR VOLUMES / 30 FT GREENHOUSE WIDTH

Length Whole greenhouse Closed blackout tunnel
60 ft 33,476 ft³ 19,988 ft³
80 ft 44,634 ft³ 26,650 ft³
100 ft 55,793 ft³ 33,313 ft³

Nominal model volumes before crop, equipment and structural displacement. Final curtain hardware affects the enclosed volume.

Choose a cooling requirement for the actual season

Summer ventilation guidance commonly starts near one greenhouse volume per minute, while crop, climate and equipment conditions determine the final design. University of Georgia Extension explains the seasonal ventilation demands.

The calculator's two-to-three-minute example is an arithmetic comparison. For the modeled 100-foot whole house, that interval corresponds to 18,598–27,896 CFM. Bring your summer design conditions and dark-period crop targets into the American Roots ventilation discussion before choosing an operating stage.

WORKED MODEL / 30 FT WIDE

Try the airflow calculation.

The geometry comes from our saved greenhouse model. Enter a flow measured or selected at the installed operating pressure.

CFM here is outside-air exhaust. Add the delivered flow of operating exhaust fans at the same system pressure.

Nominal air-exchange time2.54 min

55,793 ft³ ÷ 22,000 CFM

Flow for a 2–3 minute example
18,598–27,896 CFM
Exchanges per hour at your input
23.7
Pad face velocity, if all intake crosses the pad
212 ft/min

The pad example is 26 × 4 ft, or 104 ft². Nominal volumes exclude displacement by crops and equipment. Curtain tracks and seals remain provisional. This exchange target alone does not establish adequate cooling or humidity control.

Specify delivered flow through the complete air path

An installed exhaust fan must draw air through the selected inlets, screens, shutters, wet pads and light-control components. Those restrictions create pressure loss. The fan curve gives the airflow available at that operating pressure; its free-air rating alone is insufficient. UF/IFAS explains fan selection.

The American Roots reference layout illustrates four front exhaust positions, four lower rear intakes and two upper rear vents. Treat that as a layout to coordinate with the quoted equipment schedule. Request model, quantity, operating pressure and electrical requirements together for your greenhouse.

Match the wet wall to the airflow

Pad face velocity equals airflow through the pad divided by its exposed area. A nominal 26 × 4 ft bank has 104 square feet; 22,000 CFM through that entire area produces about 212 feet per minute. This conditional example lets you compare a proposed flow with the selected pad's performance data.

For an American Roots fan-and-pad configuration, specify the pad material, effective area, water distribution and inlet free area alongside the fans. UF/IFAS guidance explains why outside wet-bulb conditions and air warming across the house affect the cooling result.

Keep the crop air path working during blackout

SwarmDep forms an interior crop compartment. In the model's 100-foot example, a two-to-three-minute exchange of that compartment uses 11,104–16,657 CFM. The reduced volume changes the exchange calculation while the planted crop continues releasing moisture.

Develop the lower intake, light-trap and exhaust route with the closed curtain shown on the drawing. Upper-zone equipment needs its own sequence so an easier roof-space route does not bypass the crop or pad. This coordination is a central reason to select American Roots blackout and ventilation together.

Commission the system around the growing plan

Record curtain position, active fan stages, inlet position and representative crop-zone readings during commissioning. Circulation fans improve mixing inside the space; their CFM is excluded from outside-air exchange calculations. The circulation guide explains the distinction.

Use the readings to establish a practical operating reference for your American Roots greenhouse. Humidity management remains part of the dark-period plan; UMass Extension describes the role of temperature, ventilation and moisture sources.

Sources and project planning

Technical references: UGA ventilation, UF fan curves, UF fan-and-pad cooling, and UMass humidity. Model volumes describe the reference geometry; final equipment and curtain details belong in your American Roots proposal.

A FEW MORE DETAILS

Your questions, answered.

Can I add circulation-fan CFM to exhaust CFM?

Outside-air exchange uses delivered exhaust airflow. Circulation fans move air within the greenhouse and are accounted for separately.

Does a two-minute exchange certify adequate summer cooling?

Exchange time is one calculation. Cooling and humidity requirements depend on outdoor conditions, crop loads, installed airflow, pad performance and the enclosure.

Does a smaller blackout zone always need less ventilation?

Its smaller volume changes nominal exchange time, but the crop's moisture and heat loads still need to be served. Select the closed-period operating mode from those requirements.

Bring your plans to American Roots.

Choose your greenhouse and send the configuration with your location, crop and questions. We will work through the scope of your project quote with you.

Call our team: (772) 321-6305